You turn on the shower and get a weak trickle. The kitchen tap fills a kettle slowly. Yesterday everything was fine. Is it a blocked pipe, a problem with the street supply, or a leak you cannot see?
Low water pressure usually points to one of four things. The supply outside may be weak, a valve may be partly closed, a tap or showerhead may be blocked, or water may be escaping somewhere in the pipework. The quickest way to tell them apart is to ask where the problem shows up.
Is it one tap or the whole home?
Start with a simple test. Run the cold tap in the kitchen, then the bathroom, then the outside tap if you have one.
If only one outlet is weak, the problem is local. A tap aerator or a showerhead clogged with limescale is the usual cause. London has hard water in many areas, so scale builds up fast. Unscrew the aerator, soak it in a limescale remover or white vinegar for an hour, rinse it and fit it back.
If every outlet is weak, the cause sits earlier in the system. That points to the stopcock, the supply pipe or the mains water supply itself.
Check the stopcock first
The main stopcock is the valve that controls water into your home. It is often under the kitchen sink or near the front door. A stopcock that has been turned back after plumbing work may be only half open.
Turn it anticlockwise until it stops, then run a tap. Say the shower flow doubles after this. You have found the cause, and no repair is needed. If the valve is stiff or leaks around the spindle, do not force it. A damaged stopcock needs a plumber.
Check any other valves too. Some homes have an isolation valve under each sink, and a half-closed one can reduce flow to that tap alone.
Ask whether the problem is outside your home
Sometimes the weak supply is not yours. Local works, a burst main or high demand at peak times can lower pressure for a whole street. Ask a neighbour whether they have the same trouble. Your water company also publishes service updates for each area.
If the pressure falls at the same time each evening and returns later, demand is the likely cause. If it has dropped permanently, ask the water company to test the supply at your boundary.
Combi boilers and low hot water pressure
When only the hot water is weak, look at the boiler. A combi boiler heats water as it flows, so a blocked filter or scaled heat exchanger can cut the flow. Cold taps will run normally while hot ones stay weak.
Do not take a sealed boiler apart yourself. Gas appliances need a Gas Safe registered engineer for any internal work.
When a hidden leak is the cause
A leak is the cause people most often miss. Water escaping from a pipe takes some of the flow before it reaches your taps, so pressure falls even though nothing looks wrong. The pipe may run under a floor, behind a wall or below a bath.
Try this simple test. Turn off every tap and appliance, then read your water meter. Wait an hour without using any water and read it again. If the numbers have changed, water is going somewhere. Signs you can see include damp patches, a musty smell, stained ceilings or a floor that feels warm without heating on.
Take a worked example. The meter shows one reading at nine in the morning and a slightly higher reading an hour later, with every tap off. Even a small change means water has moved through the pipes while nothing was in use. Before you suspect a leak, rule out the usual harmless causes. A toilet cistern that refills slowly, a dripping tap or a garden system on a timer can also turn the dial, so check these first.
Professional help is the safest route here, because opening floors and walls on a guess can cause more damage. Water leak detection in London lets a plumber trace a hidden leak, find the damaged pipe and repair it without breaking up more than needed. You can read how it works at https://oliasplumbingandheating.co.uk/mag/water-leak-detection-london/ from Olia's Plumbing & Heating, a local team that offers a free quote.
Pressure and flow are not the same thing
People often say pressure when they mean flow. Pressure is the force that pushes water through the pipes, and flow is how much water comes out in a given time. A tap can have good pressure and still deliver little water if a scaled aerator narrows the opening. In the same way, a wide pipe on a weak supply may flow freely but without much force.
The difference matters because the remedies differ. A narrow outlet needs cleaning, a weak supply needs the water company or a pump, and a restricted pipe needs a plumber to trace it.
Pressure problems that come and go
Some homes lose pressure only at certain times. Morning showers and evening cooking overlap in many households, and the supply can struggle when several taps run together. A pressure that is fine at 2 p.m. and weak at 7 p.m. is a demand problem, not a fault in your pipes.
If you have a tank-fed system with a loft tank, the pressure also depends on the height of the tank above the tap. A bathroom on the top floor gets less pressure than the kitchen. A pump can raise it, but it needs a plumber to choose the right type.
What to do in the meantime
If you suspect a leak, close the stopcock when you leave the home for long periods. Photograph any damp patches with the date, because an insurer or landlord may ask for a record. Keep the meter readings in a note on your phone.
If water is coming through a ceiling or you cannot control it, shut the stopcock and switch off the electricity to that area if it is safe to reach the consumer unit.
What to tell the plumber or the water company
A call is more useful when you can describe the problem in a few plain facts. Say whether the weak flow affects hot water, cold water or both, and whether it is one outlet or every outlet. Add when it started, whether it changes through the day, and what the meter showed during the hour without use. These details often separate a street supply issue from a fault inside the home before anyone visits.
A short checklist
Work from the simplest cause to the hardest. Check one tap against another. Open the stopcock fully. Clean the aerators and showerheads. Ask neighbours about the street. Then read the meter. By that point you will know whether the cause is a ten-minute job or something that needs a plumber.